SHUTTING DOWN THE COMPRESSOR 1. To shut off the compressor, simply turn the ON/OFF switch to the O (OFF) position. 2. Close the air outlet tap and trigger th e equipment (spray gun, air tool etc.) to release air from the air hose before disconnecting the
Winterize Sprinkler Systems and Outdoor Faucets: Air Compressor Quick-Connect Plug To Garden Hose Faucet Blow Out Adapter with Shut Off Valve (Lead-Free Brass) 4.8 out of 5 …
Also known as air fuses, these valves close automatically to turn airflow off when air volume exceeds the shut-off flow rate. Air Signal On/Off Valves When system pressure reaches the maximum, these valves open and send an air signal to turn on a downstream device such as a discharge valve or throttle.
6) AIR TANK DRAIN VALVE: The drain valve is used to remove moisture from the air tank(s) after the air compressor is shut off. NEVER attempt to open the drain valve when more than 10 PSI of air pressure is in the air tank! To open the drain valve, turn the
Store the air compressor in a clean and dry loion. DESCRIPTION OF OPERATION DRAIN VALVE: The drain valve is loed at the bottom of the air tank and is used to drain condensation at the end of each use. AUTOMATIC SHUT OFF SYSTEM: If the 2.
Open the isolation shut ---off valve between the compressor and the compressed air system. Page 43 Maintenance 1 Ball valve 4 Filler plug 8 Screwed sealing plug A shut (oil top ---off) (oil cooler) B open 5 Oil separator tank 9 Ball valve --- oil drain 2 Pressure gauge 6 Nozzle 10 Hose coupling 3 Hose coupling 7 Oil level 11 External pressure source Unscrew the oil filler plug (4) on the oil
Flexible Blowout Hose—Control the supply of air with the compact shut-off valve. Flexible reinforced synthetic rubber hose. Easy Connection: 1/4" INDUSTRIAL air quick-connect plug and 3/4" garden hose connector. Safer, healthier, and environmentally friendlier
tank(s) after the air compressor is shut off. NEVER attempt to open the drain valve when more than 10 PSI of air pressure is in the air tank! To open the drain valve, turn the knob counterclockwise
4 309237 Installation Installation 1. Connect grounded fluid hose to the Contractort In--line valve. 2. Connect 3-ft or 6-ft extension to in--line valve. Use a wrench to tighten. 3. Connect the Cleanshott Shut--off Valve. Use a wrench to tighten. NOTE: Be sure seals (33
H. AIR OUTLET: The outlet is connected to the 1/4” (6.4 mm) NPT air hose. I. AIR TANK DRAIN VALVE: The drain valve is used to remove moisture from the air tank after the compressor is shut off. J. AIR TANK: The tank is where the compressed air is stored.
For example, a long small hose feeding a high air demand tool can result in a high-pressure drop. The result of this will mean either your compressor is working harder and using more power to keep up with your air demands, or—if it can’t keep up—your tool performance will be reduced.
This compressor is equipped with an overload protector which will shut off motor if it becomes overloaded. If the overload protector is actuated, the motor must be allowed to cool down for approximately 30 minutes before it will reset. Figure 3 Drain Valve Handle
Shut off valve is made of durable brass with a quarter-turn handle to turn air flow on and off quickly. Made with threaded ports (FPT) to connect with standard hoses or pipes. Designed to improve air hose performance.
Open the shut ---off valve (7) slowly to release pressure. Withdraw the male hose fitting and close the shut ---off valve. 10.12 Checking and Topping up the Cooling Oil 10.12.1 Check cooling oil level. Page 74 Make sure that the shut ---off
1. Turn the compressor off with the on/off switch and then unplug the cord. 2. Rotate the pressure regulator anti-clockwise until it is fully closed; check the regulated pressure gauge to ensure that it reads 0psi. 3. Also turn on the air tool to discharge any
5. Attach the desired tool to one end of an air hose and the air hose to an outlet depending on the tool or appliion. 6. Turn the compressor back on and adjust the regulated pressure to the desired level once the pump has shut off and the compressor has
harm. Wear protective gear. STOP! IN567400AV 1/15 Breathable Air Warning This compressor/pump is NOT equipped and should NOT be used “as is” to supply breathing quality air. For any appliion of air for human consumption, you must fit the air
4. Should at any time during use, your air compressor automatically shuts off; do not attempt to restart the air compressor. Turn off power and allow unit to cool for about 30 minutes. This will allow the Thermal Overload Protector to reset so you can safely resume use of the air 5.
SHUTTING DOWN THE COMPRESSOR 1. To shut off the compressor, simply turn the ON/OFF switch to the O (OFF) position. 2. Close the air outlet tap and trigger th e equipment (spray gun, air tool etc.) to release air from the air hose before disconnecting the
tank(s) after the air compressor is shut off. NEVER attempt to open the drain valve when more than 10 PSI of air pressure is in the air tank! To open the drain valve, turn the knob counterclockwise
4. Turn off the compressor, drain any liquid from the tank and close the drain valve. The compressor is now ready for use. 5. Attach the desired tool to one end of an air hose and the air hose to an outlet depending on the tool or appliion. 6. Turn the compressor
Compressed air should not be blown through any backflow device. To start the blow out, shut off the irrigation water supply and, with the compressor valve in the closed position, attach the air compressor hose to the fitting.
(bleed off) the air in the Air Compressor/ Fill hose after every use of the air compressor. 4.1 Important Features of the Air Compressor A. Automatic Pressure Shut Off Feature • The air compressor is equipped with an automatic pressure cutoff feature that will
tank(s) after the air compressor is shut off. NEVER attempt to open the drain valve when more than 10 PSI of air pressure is in the air tank! To open the drain valve, turn the knob counterclockwise
Shut off valve is made of durable brass with a quarter-turn handle to turn air flow on and off quickly. Made with threaded ports (FPT) to connect with standard hoses or pipes. Designed to improve air hose performance.
SHUTTING DOWN THE COMPRESSOR 1. To shut off the compressor, simply turn the ON/OFF switch to the O (OFF) position. 2. Close the air outlet tap and trigger th e equipment (spray gun, air tool etc.) to release air from the air hose before disconnecting the
100C Air Compressor Kit MOUNTING AND WIRING 1. Disconnect ground cable from vehicle’s battery. 2. Temporarily position the air compressor in the loion where it will be mounted. 3. Route ground wire to the negative post of the battery or to an appropriate grounding point